WALDEMAR Sheet Metal and Plate
Bending Rolls
Call to get a quote, or look at the bottom of this page for leasing options!
|
 |
Waldemar
"B" Series Initial
Pinch Sheet Metal Bending Rolls
7 gauge to 24
gauge and 3' to 10' wide |
|
 |
 |
This end view shows:
- The accurately machined heavy steel end frame.
- The heat treated alloy steel sliding bearing case assembly.
- Sealed lubed-for-life spherical roller bearings.
- The pinch roll adjustment by the time proven hardened alloy steel
wedge/screw system.
- The large bending roll adjustment hand wheel.
- WDM designed and built gear box, which houses a ground steel worm
gear and bronze worm gear and all necessary rolling element type
bearings running in grease for long life and easy adjustment.
 |
Top Picture Forward and reverse
roll rotation is accomplished by actuating the dual guarded foot switch.
Middle Picture The shaft coupling, standard is disengaged allowing
the bending roll to be angled for rolling cones.
Lower picture The roll with optional mechanical digital read-out
and infinitely variable speed. Top roll is swung out of remove work piece. |
|
|
 |
Here is a view of the Heavy Gear box/Worm Gear/ Screw,
bending roll support system. |
- The Roll is driven by a Unique Hydraulic drive arrangement. The main
electric motor only runs when work is being performed. The power is transmitted to the rolls via heavy steel gears. (The
chain drive is for the optional power bending roll adjustment)
|
 |
- Pinch roll is adjusted to metal thickness. Bending
roll is adjusted to pre-bend position. Work piece is entered from rear
of machine and engaged into starting/squaring groove
- Rolls are rotated to feed work piece into machine a
short distance, completing the pre-bend.
- Rolls are rotated in opposite directions and work
piece is removed
- Work piece is turned and re- entered from the
opposite (front) side of the machine. Bending
- roll adjusted upwards to
finish roll position
- Rolls are rotated and work piece rolled to completion
| Model |
Length |
Depth |
Height |
Weight |
Capacity |
HP |
Price |
| B-4-36 |
56" |
27-1/2" |
38" |
1505 |
10 ga x 3' |
2 |
$8790.00 |
| B-4-48 |
68" |
27-1/2" |
38" |
1700 |
12 ga x 4' |
2 |
|
| B-4-60 |
80" |
27-1/2" |
38" |
1895 |
14 ga x 5' |
2 |
|
| B-4-72 |
92" |
27-1/2" |
38" |
2090 |
16 ga x 6' |
2 |
|
| B-4-84 |
104" |
27-1/2" |
38" |
2285 |
16 ga x 7' |
2 |
|
| B-4-96 |
122" |
27-1/2" |
38" |
2680 |
20 ga x 8' |
2 |
$11995.00 |
| B-4-120 |
146" |
27-1/2" |
38" |
3600 |
24 ga x 10' |
2 |
|
| B-5-36 |
56" |
30-1/2" |
39" |
1960 |
7 ga x 3' |
3 |
|
| B-5-48 |
68" |
30-1/2" |
39" |
2230 |
8 ga x 4' |
3 |
|
| B-5-60 |
80" |
30-1/2" |
39" |
2500 |
10 ga x 5' |
3 |
$9950.00 |
| B-5-72 |
92" |
30-1/2" |
39" |
2770 |
12 ga x 6' |
3 |
|
| B-5-84 |
104" |
30-1/2" |
39" |
3040 |
14 ga x 7' |
3 |
|
| B-5-96 |
122" |
30-1/2" |
39" |
3510 |
16 ga x 8' |
3 |
|
| B-5-120 |
146" |
30-1/2" |
39" |
4050 |
18 ga x 10' |
3 |
$14525.00 |
|
 
|
Three-Roll Pinch
Pyramid Hydraulic Plate Bending Machine
Real work horses, Spherical roller tapered
roller bearings are used throughout. Optional Cone rolling attachment,
Digital read out on roll position, Bar and Angle attachments. |
 |
|
|
Four-Roll Double Pinch
Plate Bending Machine
Hydraulic cone rolling adjustment. Top and
Bottom Center Roll are powered, speeds are Hydraulically synchronized and
equalized. Many sizes available, with up to 19" diameter Rolls and up to
12' length
|
|
 |
 |
 |
Model #400-7-6 with 425-4-E Control,
Overhead Support, and Auto Ejector
Used for rolling tank shells for air
receivers manufacturing |
Model #400-11-6 with Special Grooved
Rolls and 425-4 Control
Used for aluminum silo/storage tank
staves from 2 to 6 ft wide x 10 to 100 ft diameter
|
 |
